2008 Jeep Grand Cherokee Key Stuck In Ignition

2008 Jeep Grand Cherokee Key Stuck In Ignition. This lock can bind the ignition switch and get the key stuck from time to time. Try that first if not here are instructions on how to replace the ignition key tumbler in the diagrams below.

1 Pair Volume Knob Covers Black Aluminum Alloy Volume Cd Switch Knob Ring Cap Cover Trim For Jeep Grand Cherokee 2014 2019|Auto Fastener & Clip| - Aliexpress from www.aliexpress.com

Since about a week ago my key fob gets stuck in the ignition after i turn the jeep off. Use a plastic trim removal stick (2) to remove switch bezel (1). Manipulating your grand cherokee’s steering wheel can unbind the key.

Source: www.cherokeeforum.com

The key lock cylinder may be removed without removing the switch assembly, although the original ignition key must be used. Yes no monday, july 29th, 2013 at 12:44 pm beachmom member i don't think that will fix it.

Source: www.youtube.com

Basically, the key fob gets stuck because your shift control module doesn't recognize the car is in park and has a delayed reaction. It's a little embarrassing too when trying to go out with friends and you have to wait for your key.

Source: www.youtube.com

Recently my jeep's key started acting up. Turn key to off and try getting the key out.

Source: www.justanswer.com

With the engine off, shifter in park, your foot on the break, quickly press and release the shifter button a few times. Tap the ignition lock cylinder with the plastic end of a scrwedriver (with the key removed).

Source: www.justanswer.com

Try that first if not here are instructions on how to replace the ignition key tumbler in the diagrams below. Yes no monday, july 29th, 2013 at 12:44 pm beachmom member i don't think that will fix it.

Source: www.jeepforum.com

The vehicle was taken to an authorized dealer more than five time. Since about a week ago my key fob gets stuck in the ignition after i turn the jeep off.

Source: www.denver-locksmith.net

16 people found this helpful. A drop or two of oil applied to the key hole and turning the steering wheel might do it.

Source: www.youtube.com

The only way to see it is to have the column cover off (the plastic piece that surrounds the area around the ignition), once it is off just push the lock down and the key will come out. Yes no monday, july 29th, 2013 at 12:44 pm beachmom member i don't think that will fix it.

Source: www.aliexpress.com

Chrysler group is recalling about 350,000 vehicles from the 2008 model year, including some jeep models, because of a condition that may cause the ignition key to get stuck or inadvertently move. With the engine off, shifter in park, your foot on the break, quickly press and release the shifter button a few times.

Source: blog.1aauto.com

This will temporally dislodge the solenoid cap and allow you turn the ignition to the natural position where. The key lock cylinder may be removed without removing the switch assembly, although the original ignition key must be used.

Source: www.youtube.com

Then insert the key and try to start. Please also check out the statistics and reliability analysis of the 2008 jeep grand cherokee based on all problems reported for the 2008 grand cherokee.

There Must Be Some Type Of Adjustment Somewhere Not Too Sure Though.

The contact stated that the key was stuck in the ignition several times and the failure recurred intermittently. Try that first if not here are instructions on how to replace the ignition key tumbler in the diagrams below. If you get it to turn immediately replace the igntion lock cylinder.

Only After A Hear A Clunk From The Ignition Key Area Can I Turn The Key To The Off Position And Am Able To Remove The Key.

This issue often happens with cheap duplicated keys. At the same time i used to have to press the brake to shift from park to any gear now it just moves freely without using the brake. It will not go to the off position after shutting it off.

Manipulating Your Grand Cherokee’s Steering Wheel Can Unbind The Key.

This will temporally dislodge the solenoid cap and allow you turn the ignition to the natural position where. This key must be professionally cut and programmed when received by a local automotive locksmith (click here for locksmith search ). Use a plastic trim removal stick (2) to remove switch bezel (1).

16 People Found This Helpful.

I have a 2008 jeep grand cherokee. 2008 jeep grand cherokee 3 answers. Since about a week ago my key fob gets stuck in the ignition after i turn the jeep off.

Please Also Check Out The Statistics And Reliability Analysis Of The 2008 Jeep Grand Cherokee Based On All Problems Reported For The 2008 Grand Cherokee.

Turn key to off and try getting the key out. Images (click to enlarge) sponsored links was this answer helpful? It's a little embarrassing too when trying to go out with friends and you have to wait for your key.